About Calvert Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Calvert: Robertson County Fire 154.3175 MHz, P25, NAC 411. Trunked: Texas Wide Area Radio Network (TxWARN), for example Robertson County Fire talkgroup 4130 (hex 1022).
- 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
- 2 conventional channels use a digital mode (P25), which needs a scanner that decodes that mode.
- Trunked radio systems that carry fire and EMS traffic here: Texas Wide Area Radio Network (TxWARN): 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Calvert, start with the Franklin site of Texas Wide Area Radio Network (TxWARN), about 12 miles away. Its control channels: 770.69375, 773.03125 MHz.
Data updated .
Robertson County channels that also cover Calvert
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Robertson County Fire | Fire/EMS Primary | 154.3175 In 159.3900 | NAC 411 | P25 | WQJD362 |
| Robertson County Fire | Fire/EMS Dispatch | 155.2500 In 159.0450 | 411 DPL | FMN | WPQK535 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Robertson County Fire | Fire/EMS Secondary | 154.9650 In 159.4650 | NAC 411 | P25 | WQJD362 |
Texas Wide Area Radio Network (TxWARN)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Robertson County Fire | Fire EMS Dispatch | 4130 | 1022 | D |
| Robertson County Fire | Fire EMS Response | 4131 | 1023 | D |
| Robertson County Fire | Fire EMS Response | 4132 | 1024 | D |
Nearest trunked radio sites
Distances are measured from the center of Calvert.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Calvert?
We do not have a fire dispatch channel listed specifically for Calvert. The county-level fire dispatch channels in the same county: Robertson County Fire 154.3175 MHz, P25, NAC 411.
Do fire departments and EMS use a trunked radio system in Calvert?
Yes. The county-level systems that cover Calvert are Fire and EMS talkgroups are listed for Texas Wide Area Radio Network (TxWARN): 3 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Calvert?
The analog conventional channels can be heard on any scanner; a scanner that decodes P25 is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Calvert?
For Calvert, start with the Franklin site of Texas Wide Area Radio Network (TxWARN). Its control channels are 770.69375, 773.03125 MHz. Program a control channel first; the scanner finds the voice channels from it.