About Weimar Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Weimar: Colorado County Fire 151.2500 MHz, FM, 146.2 PL. County-level ems dispatch that covers Weimar: Colorado County EMS 155.7450 MHz, FM, 723 DPL. Trunked: Texas Wide Area Radio Network (TxWARN), for example Colorado County Fire talkgroup 1756 (hex 6dc).
- 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: Texas Wide Area Radio Network (TxWARN): 10 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Weimar, start with the Fayette County site of Greater Austin/Travis Regional Radio System (GATRRS), about 9 miles away. Its control channels: 852.05 MHz.
- 1 listed entry is marked encrypted. No scanner can decode encrypted audio.
Data updated .
Weimar conventional frequencies
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Weimar Fire | Fire Mobile/Tactical | 154.3100 | FM | WPBN566 |
Colorado County channels that also cover Weimar
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Colorado County Fire | Colorado County Fire – Dispatch | 151.2500 In 153.8300 | 146.2 PL | FM | WPWG467 |
EMS Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Colorado County EMS | Colorado County EMS – Dispatch | 155.7450 In 153.9950 | 723 DPL | FM | KWF871 |
Texas Wide Area Radio Network (TxWARN)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Colorado County Fire | Colorado County Fire – Dispatch | 1756 | 6dc | D |
| Colorado County Fire | North | 1760 | 6e0 | D |
| Colorado County Fire | West | 1780 | 6f4 | D |
| Colorado County Fire | East | 1781 | 6f5 | D |
| Colorado County Fire | South | 1782 | 6f6 | D |
| Colorado County EMS | Colorado County EMS – Dispatch | 1770 | 6ea | D |
| Colorado County EMS | EMS First Responders | 1708 | 6ac | D |
| Colorado County EMS | EMS MCI | 1728 | 6c0 | D |
| Colorado County EMS | EMS MCI | 1732 | 6c4 | D |
1 encrypted talkgroup (cannot be monitored)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Colorado County Hospital | EMS to Columbus Community Hospital | 1784 | 6f8 | D Encrypted |
Nearest trunked radio sites
Distances are measured from the center of Weimar.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Weimar?
We do not have a fire dispatch channel listed specifically for Weimar. The county-level fire dispatch channels in the same county: Colorado County Fire 151.2500 MHz, FM, 146.2 PL.
What frequency does EMS or the ambulance service use in Weimar?
We do not have a EMS dispatch channel listed specifically for Weimar. The county-level EMS dispatch channels in the same county: Colorado County EMS 155.7450 MHz, FM, 723 DPL.
Do fire departments and EMS use a trunked radio system in Weimar?
Yes. The county-level systems that cover Weimar are Fire and EMS talkgroups are listed for Texas Wide Area Radio Network (TxWARN): 10 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Weimar?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Weimar?
For Weimar, start with the Fayette County site of Greater Austin/Travis Regional Radio System (GATRRS). Its control channels are 852.05 MHz. Program a control channel first; the scanner finds the voice channels from it.
Are Weimar fire and EMS frequencies encrypted?
None of the 1 conventional frequencies listed for Weimar are marked encrypted.