About Draper Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Draper: Pulaski, County of 453.5250 MHz, FM, 79.7 PL; Pulaski, Town of Fire 453.7000 MHz, FM, 74.4 PL; Radford Army Ammunition Plant Fire 166.2000 MHz, FM, no tone. County-level ems dispatch that covers Draper: Pulaski, County of 453.0250 MHz, narrow FM, 100.0 PL. Trunked: Pulaski County, for example Pulaski County EMS talkgroup 261401 (hex 3fd19).
- 6 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: Pulaski County: 1 talkgroup. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Draper, start with the Site 1.2 Simulcast site of Pulaski County, about 5 miles away. Its control channels: 453.2875 MHz.
Data updated .
Pulaski County channels that also cover Draper
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Pulaski, County of | Pulaski, County of – Dispatch | 453.5250 In 458.5250 | 79.7 PL | FM | WNXJ936 |
| Pulaski, County of | Fire/Rescue Paging | 453.8250 | FMN | WNPK310 | |
| Pulaski, Town of Fire | Pulaski, Town of Fire – Dispatch | 453.7000 | 74.4 PL | FM | KBP889 |
| Radford Army Ammunition Plant Fire | Security/Fire | 166.2000 | FM | — |
EMS Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Pulaski, County of | Pulaski, County of – Dispatch | 453.0250 In 458.0250 | 100.0 PL | FMN | WYR840 |
Hospitals & Medical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Pulaski, County of | Pulaski, County of – Ambulance to Hospital | 462.9750 | 103.5 PL | FM | WZU268 |
Pulaski County
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Pulaski County EMS | Pulaski County EMS – Dispatch | 261401 | 3fd19 | T |
Nearest trunked radio sites
Distances are measured from the center of Draper.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Draper?
We do not have a fire dispatch channel listed specifically for Draper. The county-level fire dispatch channels in the same county: Pulaski, County of 453.5250 MHz, FM, 79.7 PL; Pulaski, Town of Fire 453.7000 MHz, FM, 74.4 PL; Radford Army Ammunition Plant Fire 166.2000 MHz, FM, no tone.
What frequency does EMS or the ambulance service use in Draper?
We do not have a EMS dispatch channel listed specifically for Draper. The county-level EMS dispatch channels in the same county: Pulaski, County of 453.0250 MHz, narrow FM, 100.0 PL.
Do fire departments and EMS use a trunked radio system in Draper?
Yes. The county-level systems that cover Draper are Fire and EMS talkgroups are listed for Pulaski County: 1 talkgroup. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Draper?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Draper?
For Draper, start with the Site 1.2 Simulcast site of Pulaski County. Its control channels are 453.2875 MHz. Program a control channel first; the scanner finds the voice channels from it.