Skip to content

Bicknell Fire and EMS Frequencies

We do not have frequencies listed specifically for Bicknell in Wayne County, Utah yet. Countywide channels for Wayne County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Teasdale Peak (Utah Communications Authority (P25)), about 4 miles away.

About Bicknell Fire and EMS Frequencies

Quick answer: County-level ems dispatch that covers Bicknell: Wayne County EMS 155.2800 MHz, narrow FM, CSQ. Trunked: Utah Communications Authority (P25) (Project 25), for example Wayne County Fire talkgroup 9302 (hex 2456).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Utah Communications Authority (P25) (Project 25): 4 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Bicknell, start with the Teasdale Peak site of Utah Communications Authority (P25), about 4 miles away. Its control channels: 769.41875, 773.93125 MHz.

Data updated .

Wayne County channels that also cover Bicknell

EMS Dispatch

EMS Dispatch frequencies for Wayne County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Wayne County EMSEMS paging/ambulance155.2800CSQFMNWQCE439

Utah Communications Authority (P25)

Project 25 · System ID 00A

Utah Communications Authority (P25) talkgroups
AgencyDescriptionTalkgroupHexMode
Wayne County FireWayne County Fire – Dispatch93022456T
Wayne County FireCar to Car93202468T
Wayne County EMSWayne County EMS – Dispatch93012455T
Wayne County EMSCar to Car93212469T

Nearest trunked radio sites

Distances are measured from the center of Bicknell.

Teasdale Peak · Utah Communications Authority (P25)
Project 25 · RFSS 103 · Site 103 (hex 67) · NAC 1F7 · about 4 mi away
Control 769.41875, 773.93125
Voice 772.55625, 772.86875, 773.21875
Fremont · Utah Communications Authority (P25)
Project 25 · RFSS 143 · Site 143 (hex 8F) · NAC 21F · about 13 mi away
Control 769.30625, 774.63125
Voice 770.78125, 772.19375
Pipe Springs · Utah Communications Authority (P25)
Project 25 · RFSS 93 · Site 93 (hex 5D) · NAC FFD · about 37 mi away
Control 769.58125, 774.68125
Voice 771.15625, 772.26875, 773.43125
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does EMS or the ambulance service use in Bicknell?

We do not have a EMS dispatch channel listed specifically for Bicknell. The county-level EMS dispatch channels in the same county: Wayne County EMS 155.2800 MHz, narrow FM, CSQ.

Do fire departments and EMS use a trunked radio system in Bicknell?

Yes. The county-level systems that cover Bicknell are Fire and EMS talkgroups are listed for Utah Communications Authority (P25) (Project 25): 4 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Bicknell?

The analog conventional channels can be heard on any scanner; a trunking scanner that supports Project 25 is needed for the trunked talkgroups.

What are the control channels for trunked radio in Bicknell?

For Bicknell, start with the Teasdale Peak site of Utah Communications Authority (P25). Its control channels are 769.41875, 773.93125 MHz. Program a control channel first; the scanner finds the voice channels from it.