Skip to content

Blum Fire and EMS Frequencies

We do not have frequencies listed specifically for Blum in Hill County, Texas yet. Countywide channels for Hill County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Blum (Hill County), about 5 miles away.

About Blum Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Blum: Hill County Fire 154.0475 MHz, narrow FM, 532 DPL. County-level ems dispatch that covers Blum: Hill County EMS 460.3875 MHz, narrow FM, 192.8 PL. Trunked: Hill County, for example Hill County Fire talkgroup 41200 (hex a0f0).

  • 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Hill County: 13 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Blum, start with the Blum site of Hill County, about 5 miles away. Its control channels: 854.5625, 858.275, 859.275 MHz.

Data updated .

Hill County channels that also cover Blum

Fire Dispatch

Fire Dispatch frequencies for Hill County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Hill County FireCounty Fire Dispatch (new)154.0475
In 158.9700
532 DPLFMNWQIB690
Hill County FireCounty Fire / EMS154.2950
In 153.8300
100.0 PLFMNWPCH495

EMS Dispatch

EMS Dispatch frequencies for Hill County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Hill County EMSCareflight Ground Ambulance460.3875
In 465.3875
192.8 PLFMNWQLE331

Hill County

Hill County talkgroups
AgencyDescriptionTalkgroupHexMode
Hill County FireHill County Fire – Dispatch41200a0f0T
Hill County FireHill County Fire – Dispatch41201a0f1T
Hill County FireHill County Fire – Fire Ground41202a0f2T
Hill County FireHill County Fire – Fire Ground41203a0f3T
Hill County FireHill County Fire – Fire Ground41204a0f4T
Hill County FireFire Training West41207a0f7T
Hill County FireFire Training East41208a0f8T
Hill County FireFire Training41209a0f9T
Hill County FireFire Events41210a0faT
Hill County FireFire Events41211a0fbT
Hill County FireFire TT41205a0f5T
Hill County FireFire Talkaround41206a0f6T
Hill County FireCareflite Ground41300a154T

Nearest trunked radio sites

Distances are measured from the center of Blum.

Blum · Hill County
RFSS 5 · Site 5 (hex 5) · NAC F · about 5 mi away
Control 854.5625, 858.275, 859.275
SW Johnson Co · North Texas Interoperable Radio Network (NTIRN)
RFSS 1 · Site 9 (hex 9) · NAC 445 · about 6 mi away
Control 772.58125, 772.83125
Voice 772.33125
Johnson Co Simulcast · North Texas Interoperable Radio Network (NTIRN)
RFSS 1 · Site 4 (hex 4) · NAC 440 · about 13 mi away
Control 770.36875, 770.61875, 770.86875, 771.18125
Voice 769.08125, 769.34375, 769.59375, 770.11875
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Blum?

We do not have a fire dispatch channel listed specifically for Blum. The county-level fire dispatch channels in the same county: Hill County Fire 154.0475 MHz, narrow FM, 532 DPL.

What frequency does EMS or the ambulance service use in Blum?

We do not have a EMS dispatch channel listed specifically for Blum. The county-level EMS dispatch channels in the same county: Hill County EMS 460.3875 MHz, narrow FM, 192.8 PL.

Do fire departments and EMS use a trunked radio system in Blum?

Yes. The county-level systems that cover Blum are Fire and EMS talkgroups are listed for Hill County: 13 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Blum?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Blum?

For Blum, start with the Blum site of Hill County. Its control channels are 854.5625, 858.275, 859.275 MHz. Program a control channel first; the scanner finds the voice channels from it.