Skip to content

Industry Fire and EMS Frequencies

We do not have frequencies listed specifically for Industry in Austin County, Texas yet. Countywide channels for Austin County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Bleiblerville (Texas Wide Area Radio Network (TxWARN)), about 4 miles away.

About Industry Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Industry: Austin County Fire 154.3250 MHz, FM, 107.2 PL. Trunked: Texas Wide Area Radio Network (TxWARN), for example Austin County Fire talkgroup 2305 (hex 901).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Texas Wide Area Radio Network (TxWARN): 7 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Industry, start with the Bleiblerville site of Texas Wide Area Radio Network (TxWARN), about 4 miles away. Its control channels: 853.3375, 853.8 MHz.

Data updated .

Austin County channels that also cover Industry

Fire Dispatch

Fire Dispatch frequencies for Austin County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Austin County FireFire/EMS Primary (except Bellville)154.3250
In 156.0750
107.2 PLFMWPMR424

EMS Talk-around

EMS Talk-around frequencies for Austin County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Austin County EMSEMS Talkaround (Channel 8)158.8650107.2 PLFMKB94611

Texas Wide Area Radio Network (TxWARN)

Texas Wide Area Radio Network (TxWARN) talkgroups
AgencyDescriptionTalkgroupHexMode
Austin County FireAustin County Fire – Dispatch2305901D
Austin County FireAustin County Fire – Tactical Channel22448c4D
Austin County FireAustin County Fire – Tactical Channel22458c5D
Austin County FireAustin County Fire – Tactical Channel2306902D
Austin County EMSAustin County EMS – Dispatch2308904D
Austin County EMSAustin County EMS – Tactical Channel2309905D
Austin County EMSEMS Supervisors12314cfD

Nearest trunked radio sites

Distances are measured from the center of Industry.

Bleiblerville · Texas Wide Area Radio Network (TxWARN)
RFSS 1 · Site 20 (hex 14) · about 4 mi away
Control 853.3375, 853.8
Voice 851.125, 851.4125, 851.8125, 852.3375
San Felipe · Texas Wide Area Radio Network (TxWARN)
RFSS 1 · Site 19 (hex 13) · NAC 1A0 · about 12 mi away
Control 853.3, 853.5875
Voice 851.3375, 851.5875, 852.0875, 853.0625
Brenham · Texas Wide Area Radio Network (TxWARN)
RFSS 1 · Site 24 (hex 18) · NAC 1A1 · about 13 mi away
Control 772.70625, 774.44375
Voice 770.54375, 771.70625, 772.31875
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Industry?

We do not have a fire dispatch channel listed specifically for Industry. The county-level fire dispatch channels in the same county: Austin County Fire 154.3250 MHz, FM, 107.2 PL.

Do fire departments and EMS use a trunked radio system in Industry?

Yes. The county-level systems that cover Industry are Fire and EMS talkgroups are listed for Texas Wide Area Radio Network (TxWARN): 7 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Industry?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Industry?

For Industry, start with the Bleiblerville site of Texas Wide Area Radio Network (TxWARN). Its control channels are 853.3375, 853.8 MHz. Program a control channel first; the scanner finds the voice channels from it.