Skip to content

Beatty Fire and EMS Frequencies

We do not have frequencies listed specifically for Beatty in Klamath County, Oregon yet. Countywide channels for Klamath County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Walker Mtn (Oregon State Radio Project), about 64 miles away.

About Beatty Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Beatty: Klamath County Fire 154.0700 MHz, narrow FM, 192.8 PL. Trunked: Oregon State Radio Project, for example Klamath County Fire talkgroup 40922 (hex 9fda).

  • 11 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Oregon State Radio Project: 1 talkgroup. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Beatty, start with the Walker Mtn site of Oregon State Radio Project, about 64 miles away. Its control channels: 769.20625, 770.70625, 773.31875 MHz.

Data updated .

Klamath County channels that also cover Beatty

Fire Dispatch

Fire Dispatch frequencies for Klamath County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Klamath County FireFire District – Firecom154.0700192.8 PLFMNKNIQ200
Klamath County FireFire District 2154.4450FMN—
Klamath County FireFire District 4453.7125FMN—
Klamath County FireFire District 5458.7125FMN—

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Klamath County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Klamath County FireFire District – East County Working153.8900FMNWPKF637
Klamath County FireCounty Fire Tactical153.8900
In 154.4150
151.4 PLFMNKNAW669
Klamath County FireFire District – Central County Working153.9500FMNWZU636
Klamath County FireFire District – North County Working154.1750FMN—
Klamath County FireFire District – South County Working (1)154.3550FMNKNBL289
Klamath County FireSearch and Rescue155.1600FMNKTO395
Klamath County FireFire District – South County Working (2)155.8200FMNKON936

Oregon State Radio Project

Oregon State Radio Project talkgroups
AgencyDescriptionTalkgroupHexMode
Klamath County FireKlamath County Fire – Dispatch409229fdaT

Nearest trunked radio sites

Distances are measured from the center of Beatty.

Walker Mtn · Oregon State Radio Project
RFSS 31 · Site 31 (hex 1F) · NAC 01F · about 64 mi away
Control 769.20625, 770.70625, 773.31875, 773.80625, 774.54375
Central Simulcast · Emergency Communications of Southern Oregon
RFSS 1 · Site 4 (hex 4) · NAC 1 · about 80 mi away
Voice 769.25625, 771.05625
North Simulcast · Emergency Communications of Southern Oregon
RFSS 1 · Site 1 (hex 1) · NAC 1 · about 80 mi away
Voice 154.0325, 154.085, 154.1975
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Beatty?

We do not have a fire dispatch channel listed specifically for Beatty. The county-level fire dispatch channels in the same county: Klamath County Fire 154.0700 MHz, narrow FM, 192.8 PL.

Do fire departments and EMS use a trunked radio system in Beatty?

Yes. The county-level systems that cover Beatty are Fire and EMS talkgroups are listed for Oregon State Radio Project: 1 talkgroup. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Beatty?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Beatty?

For Beatty, start with the Walker Mtn site of Oregon State Radio Project. Its control channels are 769.20625, 770.70625, 773.31875, 773.80625 MHz. Program a control channel first; the scanner finds the voice channels from it.