Skip to content

Chase County Fire and EMS Frequencies

Chase County in Kansas has 1 countywide conventional frequency and 2 countywide talkgroups in our database. Use the list of 21 cities and communities below for local fire departments and EMS agencies.

About Chase County Fire and EMS Frequencies

Quick answer: Fire dispatch for Chase County: Chase County Fire 453.1750 MHz, narrow FM, 156.7 PL. Trunked: Kansas Statewide Interoperable Communication System (KSICS), for example Chase County Fire talkgroup 4446 (hex 115e).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Kansas Statewide Interoperable Communication System (KSICS): 2 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Chase County, start with the Cottonwood Falls site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels: 852.4875, 852.775 MHz.

Data updated .

Chase County conventional frequencies

Fire Dispatch

Fire Dispatch frequencies for Chase County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Chase County FireChase County Fire – Dispatch453.1750
In 458.1750
156.7 PLFMNKNNJ576

Chase County trunked talkgroups

Kansas Statewide Interoperable Communication System (KSICS)

Kansas Statewide Interoperable Communication System (KSICS) talkgroups
AgencyDescriptionTalkgroupHexMode
Chase County FireCounty Fire Dispatch4446115eD
Chase County EMSChase County EMS – Dispatch44571169D

Radio system sites in Chase County

Program the control channel first; your scanner finds the voice channels from it.

Cottonwood Falls · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 14 (hex E) · NAC 1B0
Control 852.4875, 852.775
Voice 851.7125, 853.075, 853.425, 853.725
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Cities & communities in Chase County

Common questions

What frequency does the fire department use in Chase County?

Fire dispatch channels listed for Chase County: Chase County Fire 453.1750 MHz, narrow FM, 156.7 PL.

Do fire departments and EMS use a trunked radio system in Chase County?

Yes. Fire and EMS talkgroups are listed for Kansas Statewide Interoperable Communication System (KSICS): 2 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Chase County?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Chase County?

For Chase County, start with the Cottonwood Falls site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels are 852.4875, 852.775 MHz. Program a control channel first; the scanner finds the voice channels from it.

Are Chase County fire and EMS frequencies encrypted?

None of the 1 conventional frequencies listed for Chase County are marked encrypted.

Are Chase County fire and EMS talkgroups encrypted?

None of the 2 talkgroups listed for Chase County are marked encrypted.