Skip to content

Melbourne Fire and EMS Frequencies

We do not have frequencies listed specifically for Melbourne in Marshall County, Iowa yet. Countywide channels for Marshall County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Marshalltown (Iowa Statewide Interoperable Communications System (ISICS)), about 10 miles away.

About Melbourne Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Melbourne: Marshall County Fire 154.3850 MHz, narrow FM, 82.5 PL. County-level ems dispatch that covers Melbourne: Marshall County EMS 155.1600 MHz, narrow FM, no tone.

  • 4 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.

Data updated .

Marshall County channels that also cover Melbourne

Fire Dispatch

Fire Dispatch frequencies for Marshall County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Marshall County FireMarshall County Fire – Dispatch154.3850
In 159.0375
82.5 PLFMNKGK678

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Marshall County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Marshall County FireMarshall County Fire – Fire Ground151.1525CSQFMNKGK678
Marshall County FireMarshall County Fire – Fire Ground159.3750CSQFMNKGK678

EMS Dispatch

EMS Dispatch frequencies for Marshall County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Marshall County EMSEMS Paging155.1600FMNWYK322

Nearest trunked radio sites

Distances are measured from the center of Melbourne.

Marshalltown · Iowa Statewide Interoperable Communications System (ISICS)
RFSS 1 · Site 64 (hex 40) · NAC 4C1 · about 10 mi away
Control 773.83125, 774.08125, 774.33125
Voice 773.08125, 773.33125, 773.58125
Site-1 · Iowa State University
Site 1 (hex 1) · about 20 mi away
Control 859.5625, 860.5625
Voice 856.5625, 857.5625, 858.5625
Newton · Iowa Statewide Interoperable Communications System (ISICS)
RFSS 1 · Site 69 (hex 45) · NAC 4C1 · about 22 mi away
Control 769.44375, 770.69375, 770.94375
Voice 769.19375
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Melbourne?

We do not have a fire dispatch channel listed specifically for Melbourne. The county-level fire dispatch channels in the same county: Marshall County Fire 154.3850 MHz, narrow FM, 82.5 PL.

What frequency does EMS or the ambulance service use in Melbourne?

We do not have a EMS dispatch channel listed specifically for Melbourne. The county-level EMS dispatch channels in the same county: Marshall County EMS 155.1600 MHz, narrow FM, no tone.

What scanner do I need to listen to fire and EMS in Melbourne?

The analog conventional channels can be heard on any scanner.

What are the control channels for trunked radio in Melbourne?

For Melbourne, start with the Marshalltown site of Iowa Statewide Interoperable Communications System (ISICS). Its control channels are 773.83125, 774.08125, 774.33125 MHz. Program a control channel first; the scanner finds the voice channels from it.