About Williams Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Williams: Hamilton County Fire 154.2350 MHz, narrow FM, no tone. County-level ems dispatch that covers Williams: Hamilton County Hospital 155.3400 MHz, FM, CSQ. Trunked: Iowa Statewide Interoperable Communications System (ISICS), for example Williams Fire talkgroup 31039 (hex 793f).
- 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: Iowa Statewide Interoperable Communications System (ISICS): 1 talkgroup; Iowa Statewide Interoperable Communications System (ISICS): 8 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Williams, start with the Hamilton Co Simulcast site of Iowa Statewide Interoperable Communications System (ISICS), about 12 miles away. Its control channels: 774.79375 MHz.
Data updated .
Williams trunked talkgroups
Iowa Statewide Interoperable Communications System (ISICS)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Williams Fire | Williams Fire Page | 31039 | 793f | T |
Hamilton County channels that also cover Williams
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Hamilton County Fire | Hamilton County Fire – Dispatch | 154.2350 In 159.0450 | FMN | WQGS402 |
EMS Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Hamilton County Hospital | Hamilton County Hospital – Dispatch (167.9PL on Base side) | 155.3400 | CSQ | FM | KQS751 |
Hospitals & Medical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Hamilton County Hospital | Hamilton County Hospital – Paging | 155.8650 | CSQ | FM | WSL644 |
Iowa Statewide Interoperable Communications System (ISICS)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Hamilton County Fire | Hamilton County Fire – Dispatch | 31008 | 7920 | T |
| Hamilton County Fire | Fire/EMS Roam | 31017 | 7929 | T |
| Hamilton County Fire | Jewell Fire Page | 31034 | 793a | T |
| Hamilton County Fire | Dispatch VHF Patch | 31045 | 7945 | T |
| Hamilton Webster City Fire | Hamilton Webster City Fire – Dispatch | 31040 | 7940 | T |
| Hamilton County Fire | County Fire | 31006 | 791e | T |
| Hamilton County EMS | EMS Operations | 31018 | 792a | T |
| Hamilton County EMS | Van Diest EMS Dispatch | 31042 | 7942 | T |
Nearest trunked radio sites
Distances are measured from the center of Williams.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Williams?
We do not have a fire dispatch channel listed specifically for Williams. The county-level fire dispatch channels in the same county: Hamilton County Fire 154.2350 MHz, narrow FM, no tone.
What frequency does EMS or the ambulance service use in Williams?
We do not have a EMS dispatch channel listed specifically for Williams. The county-level EMS dispatch channels in the same county: Hamilton County Hospital 155.3400 MHz, FM, CSQ.
Do fire departments and EMS use a trunked radio system in Williams?
Yes. Fire and EMS talkgroups are listed for Iowa Statewide Interoperable Communications System (ISICS): 1 talkgroup. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Williams?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Williams?
For Williams, start with the Hamilton Co Simulcast site of Iowa Statewide Interoperable Communications System (ISICS). Its control channels are 774.79375 MHz. Program a control channel first; the scanner finds the voice channels from it.
Are Williams fire and EMS talkgroups encrypted?
None of the 1 talkgroups listed for Williams are marked encrypted.