About Rippey Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Rippey: Greene County Fire 154.2050 MHz, narrow FM, 192.8 PL. County-level ems dispatch that covers Rippey: Greene County EMS 155.8350 MHz, narrow FM, no tone. Trunked: Iowa Statewide Interoperable Communications System (ISICS), for example Greene County Fire talkgroup 30401 (hex 76c1).
- 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: Iowa Statewide Interoperable Communications System (ISICS): 4 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Rippey, start with the Jefferson site of Iowa Statewide Interoperable Communications System (ISICS), about 11 miles away. Its control channels: 771.46875, 771.76875, 772.56875 MHz.
Data updated .
Greene County channels that also cover Rippey
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Greene County Fire | Greene County Fire – Dispatch | 154.2050 | 192.8 PL | FMN | KNAZ313 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Greene County Fire | Greene County Fire – Fire Ground | 153.8150 | 192.8 PL | FMN | WQGQ489 |
EMS Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Greene County EMS | EMS/Siren Control | 155.8350 | FMN | WYD922 |
Iowa Statewide Interoperable Communications System (ISICS)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Greene County Fire | Greene County Fire – Dispatch | 30401 | 76c1 | T |
| Greene County Fire | Fire/EMS Tactical | 30402 | 76c2 | T |
| Greene County Fire | Fire/EMS Tactical | 30403 | 76c3 | T |
| Greene County Fire | Greene County Fire – Fire Ground | 30418 | 76d2 | T |
Nearest trunked radio sites
Distances are measured from the center of Rippey.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Rippey?
We do not have a fire dispatch channel listed specifically for Rippey. The county-level fire dispatch channels in the same county: Greene County Fire 154.2050 MHz, narrow FM, 192.8 PL.
What frequency does EMS or the ambulance service use in Rippey?
We do not have a EMS dispatch channel listed specifically for Rippey. The county-level EMS dispatch channels in the same county: Greene County EMS 155.8350 MHz, narrow FM, no tone.
Do fire departments and EMS use a trunked radio system in Rippey?
Yes. The county-level systems that cover Rippey are Fire and EMS talkgroups are listed for Iowa Statewide Interoperable Communications System (ISICS): 4 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Rippey?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Rippey?
For Rippey, start with the Jefferson site of Iowa Statewide Interoperable Communications System (ISICS). Its control channels are 771.46875, 771.76875, 772.56875 MHz. Program a control channel first; the scanner finds the voice channels from it.