Skip to content

Beaver Fire and EMS Frequencies

We do not have frequencies listed specifically for Beaver in Boone County, Iowa yet. Countywide channels for Boone County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Boxholm (Iowa Statewide Interoperable Communications System (ISICS)), about 10 miles away.

About Beaver Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Beaver: Boone County Fire 154.4000 MHz, narrow FM, CSQ. Trunked: Iowa Statewide Interoperable Communications System (ISICS), for example Boone County Fire talkgroup 18506 (hex 484a).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Iowa Statewide Interoperable Communications System (ISICS): 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Beaver, start with the Boxholm site of Iowa Statewide Interoperable Communications System (ISICS), about 10 miles away. Its control channels: 770.94375, 774.56875, 774.81875 MHz.

Data updated .

Boone County channels that also cover Beaver

Fire Dispatch

Fire Dispatch frequencies for Boone County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Boone County FireBoone County Fire – Dispatch154.4000
In 159.0150
CSQFMNWQDL877

Hospitals & Medical

Hospitals & Medical frequencies for Boone County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Boone County HospitalBoone County Hospital155.3250110.9 PLFMNKJN742

Iowa Statewide Interoperable Communications System (ISICS)

Iowa Statewide Interoperable Communications System (ISICS) talkgroups
AgencyDescriptionTalkgroupHexMode
Boone County FireFire/EMS Dispatch18506484aT
Boone County FireBoone County Fire – Tactical Channel18526485eT
Boone County FireBoone County Fire – Tactical Channel18527485fT

Nearest trunked radio sites

Distances are measured from the center of Beaver.

Boxholm · Iowa Statewide Interoperable Communications System (ISICS)
RFSS 2 · Site 8 (hex 8) · NAC 4C9 · about 10 mi away
Control 770.94375, 774.56875, 774.81875
Voice 770.69375
Jefferson · Iowa Statewide Interoperable Communications System (ISICS)
RFSS 2 · Site 37 (hex 25) · about 14 mi away
Control 771.46875, 771.76875, 772.56875
Harcourt · Iowa Statewide Interoperable Communications System (ISICS)
RFSS 2 · Site 94 (hex 5E) · NAC 4C1 · about 16 mi away
Control 769.94375, 770.19375, 770.44375
Voice 769.69375
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Beaver?

We do not have a fire dispatch channel listed specifically for Beaver. The county-level fire dispatch channels in the same county: Boone County Fire 154.4000 MHz, narrow FM, CSQ.

Do fire departments and EMS use a trunked radio system in Beaver?

Yes. The county-level systems that cover Beaver are Fire and EMS talkgroups are listed for Iowa Statewide Interoperable Communications System (ISICS): 3 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Beaver?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Beaver?

For Beaver, start with the Boxholm site of Iowa Statewide Interoperable Communications System (ISICS). Its control channels are 770.94375, 774.56875, 774.81875 MHz. Program a control channel first; the scanner finds the voice channels from it.