About Washington County Fire and EMS Frequencies
Quick answer: Fire dispatch for Washington County: Washington County Fire 155.4900 MHz, narrow FM, 167.9 PL. EMS dispatch for Washington County: Washington County EMS 155.9025 MHz, NXDN48, RAN 22. Trunked: Indiana Project Hoosier SAFE-T, for example Washington County Fire talkgroup 21694 (hex 54be).
- 5 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- 1 conventional channel uses a digital mode (NXDN48), which needs a scanner that decodes that mode.
- Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Washington County, start with the Fleenortown site of Indiana Project Hoosier SAFE-T. Its control channels: 853.4625, 855.7125 MHz.
Data updated .
Washington County conventional frequencies
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Washington County Fire | Washington County Fire – Repeater | 155.4900 In 153.9950 | 167.9 PL | FMN | WQF450 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Washington County Fire | Washington County Fire – Posey Twp | 151.2725 In 159.3225 | FMN | WQFB901 | |
| Washington County Fire | Washington County Fire – Tactical Channel | 153.9950 | FMN | WQF450 | |
| Washington County Fire | Washington County Fire – Tactical Channel | 154.1900 | 167.9 PL | FMN | WQF450 |
| Washington County Fire | Emergency Management Agency | 155.9400 | FMN | WNKG271 |
EMS Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Washington County EMS | Washington County EMS – Dispatch | 155.9025 | RAN 22 | NXDN48 | WQF450 |
Washington County trunked talkgroups
Indiana Project Hoosier SAFE-T
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Washington County Fire | Washington County Fire – Dispatch (County) | 21694 | 54be | D |
| Washington County Fire | Washington County Fire – Operations (County) | 21695 | 54bf | D |
| Washington County Fire | Washington County Fire – Tactical Channel (County) | 21696 | 54c0 | D |
| Washington County EMS | Washington County EMS – Dispatch (County) | 21691 | 54bb | D |
| Washington County EMS | Washington County EMS – Operations (County) | 21692 | 54bc | D |
| Washington County EMS | Washington County EMS – Tactical Channel (County) | 21693 | 54bd | D |
Radio system sites in Washington County
Program the control channel first; your scanner finds the voice channels from it.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Cities & communities in Washington County
- Bartle
- Becks Mill
- Blue River
- Brimstone Corners
- Brown
- Bunker Hill
- Campbellsburg
- Canton
- Claysville
- Daisy Hill
- Fairview
- Farabee
- Fayetteville
- Franklin
- Fredericksburg
- Georgetown
- Gibson
- Gooseport
- Haleysbury
- Hardinsburg
- Harristown
- Highland
- Hitchcock
- Howard
- Jackson
- Jefferson
- Kossuth
- Little York
- Livonia
- Madison
- Martinsburg
- McKinley
- Millport
- Monroe
- Mount Carmel
- New Liberty
- New Pekin
- New Philadelphia
- New Salem
- Old Pekin
- Organ Springs
- Pekin
- Pierce
- Plattsburg
- Polk
- Posey
- Prowsville
- Pumpkin Center
- Rosebud
- Rush Creek Valley
- Salem
- Saltillo
- Shorts Corner
- Smedley
- South Boston
- Vernon
- Washington
Common questions
What frequency does the fire department use in Washington County?
Fire dispatch channels listed for Washington County: Washington County Fire 155.4900 MHz, narrow FM, 167.9 PL.
What frequency does EMS or the ambulance service use in Washington County?
EMS dispatch channels listed for Washington County: Washington County EMS 155.9025 MHz, NXDN48, RAN 22.
Do fire departments and EMS use a trunked radio system in Washington County?
Yes. Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Washington County?
The analog conventional channels can be heard on any scanner; a scanner that decodes NXDN48 is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Washington County?
For Washington County, start with the Fleenortown site of Indiana Project Hoosier SAFE-T. Its control channels are 853.4625, 855.7125 MHz. Program a control channel first; the scanner finds the voice channels from it.
Are Washington County fire and EMS frequencies encrypted?
None of the 6 conventional frequencies listed for Washington County are marked encrypted.
Are Washington County fire and EMS talkgroups encrypted?
None of the 6 talkgroups listed for Washington County are marked encrypted.