About Powell Fire and EMS Frequencies
Quick answer: Fire dispatch for Powell: Powell Fire 154.4000 MHz, narrow FM, 100.0 PL. EMS dispatch for Powell: Powell EMS 155.2800 MHz, narrow FM, no tone. Trunked: WyoLink, for example Powell Fire talkgroup 13925 (hex 3665).
- 8 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: WyoLink: 3 talkgroups; WyoLink: 4 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Powell, start with the McCullough Peaks site of WyoLink, about 13 miles away. Its control channels: 152.51, 152.54 MHz.
Data updated .
Powell conventional frequencies
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Powell Fire | Powell Fire | 154.4000 In 153.9500 | 100.0 PL | FMN | WNDM942 |
| Powell Fire | Powell DPW/Fire/Police – Common | 158.8800 | FMN | KLR391 |
EMS Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Powell EMS | PVHC Ambulance | 155.2800 | FMN | WQJA510 |
Powell trunked talkgroups
WyoLink
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Powell Fire | Powell Fire – Dispatch | 13925 | 3665 | D |
| Powell Fire | Powell Fire – Fire Ground | 13926 | 3666 | D |
| Powell Hospital | Powell Valley Hospital | 13901 | 364d | D |
Park County channels that also cover Powell
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Meeteese Fire | Meeteese Fire | 154.2500 | FMN | KNFT983 | |
| Meeteese Fire | Meeteese Police/Fire/DPW – Common | 155.9550 | FMN | KNFS538 | |
| Park County Fire | Park County Fire/EMS (previously 100.0 PL, now CSQ) | 155.7900 In 154.7700 | CSQ | FMN | WZX510 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Clark Fire | Clark Fire Department Tactical | 155.8125 | CSQ | FMN | WQNU210 |
EMS Talk-around
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Meeteese EMS | Meeteese EMS | 155.3400 | FMN | KNFU404 |
WyoLink
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Park County Fire | Fire 2 Powell | 13912 | 3658 | D |
| Park County EMS | Park County EMS – Dispatch | 13913 | 3659 | D |
| Park County EMS | Park County EMS – Dispatch | 13914 | 365a | D |
| Park County EMS | Cody Regional Ambulance Paging | 20121 | 4e99 | D |
Nearest trunked radio sites
Distances are measured from the center of Powell.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Powell?
Fire dispatch channels listed for Powell: Powell Fire 154.4000 MHz, narrow FM, 100.0 PL.
What frequency does EMS or the ambulance service use in Powell?
EMS dispatch channels listed for Powell: Powell EMS 155.2800 MHz, narrow FM, no tone.
Do fire departments and EMS use a trunked radio system in Powell?
Yes. Fire and EMS talkgroups are listed for WyoLink: 3 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Powell?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Powell?
For Powell, start with the McCullough Peaks site of WyoLink. Its control channels are 152.51, 152.54 MHz. Program a control channel first; the scanner finds the voice channels from it.
Are Powell fire and EMS frequencies encrypted?
None of the 3 conventional frequencies listed for Powell are marked encrypted.
Are Powell fire and EMS talkgroups encrypted?
None of the 3 talkgroups listed for Powell are marked encrypted.