Skip to content

Hammel Fire and EMS Frequencies

We do not have frequencies listed specifically for Hammel in Taylor County, Wisconsin yet. Countywide channels for Taylor County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Perkinstown (WISCOM), about 7 miles away.

About Hammel Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Hammel: Taylor County Fire 154.1750 MHz, narrow FM, 88.5 PL. Trunked: WISCOM, for example Taylor County Fire talkgroup 61007 (hex ee4f).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: WISCOM: 1 talkgroup. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Hammel, start with the Perkinstown site of WISCOM, about 7 miles away. Its control channels: 139.4125, 152.0375, 152.2025 MHz.

Data updated .

Taylor County channels that also cover Hammel

Fire Dispatch

Fire Dispatch frequencies for Taylor County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Taylor County FireCounty Fire154.1750
In 158.9775
88.5 PLFMNKFB804

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Taylor County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Taylor County FireCounty Fireground154.310088.5 PLFMNWNXQ581

WISCOM

WISCOM talkgroups
AgencyDescriptionTalkgroupHexMode
Taylor County FireTaylor County Fire61007ee4fD

Nearest trunked radio sites

Distances are measured from the center of Hammel.

Perkinstown · WISCOM
RFSS 1 · Site 110 (hex 6E) · NAC B07 · about 7 mi away
Control 139.4125, 152.0375, 152.2025
Voice 154.415, 155.655
Medford · WISCOM
RFSS 1 · Site 161 (hex A1) · NAC B06 · about 8 mi away
Control 151.2275, 154.025, 154.785, 155.925
Bellinger · WISCOM
RFSS 1 · Site 162 (hex A2) · NAC B03 · about 15 mi away
Control 151.0775, 151.3325, 154.665, 155.7075
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Hammel?

We do not have a fire dispatch channel listed specifically for Hammel. The county-level fire dispatch channels in the same county: Taylor County Fire 154.1750 MHz, narrow FM, 88.5 PL.

Do fire departments and EMS use a trunked radio system in Hammel?

Yes. The county-level systems that cover Hammel are Fire and EMS talkgroups are listed for WISCOM: 1 talkgroup. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Hammel?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Hammel?

For Hammel, start with the Perkinstown site of WISCOM. Its control channels are 139.4125, 152.0375, 152.2025 MHz. Program a control channel first; the scanner finds the voice channels from it.