Skip to content

Sumner Fire and EMS Frequencies

We do not have frequencies listed specifically for Sumner in Jefferson County, Wisconsin yet. Countywide channels for Jefferson County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Milton (WISCOM), about 8 miles away.

About Sumner Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Sumner: Jefferson County Fire 154.0550 MHz, narrow FM, 107.2 PL.

  • 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • 1 conventional channel uses a digital mode (P25), which needs a scanner that decodes that mode.

Data updated .

Jefferson County channels that also cover Sumner

Fire Dispatch

Fire Dispatch frequencies for Jefferson County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Jefferson County FireJefferson County Fire – Paging154.0550107.2 PLFMNWNGN313
Jefferson County FireJefferson County Fire – Dispatch154.3700
In 153.7700
NAC 280P25WQB793

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Jefferson County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Jefferson County FireJefferson County Fire – Fire Ground154.4150107.2 PLFMNWQB793

EMS Talk-around

EMS Talk-around frequencies for Jefferson County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Jefferson County EMSFort Healthcare – Patient Reports155.340097.4 PLFMN—

Nearest trunked radio sites

Distances are measured from the center of Sumner.

Milton · WISCOM
RFSS 1 · Site 10 (hex A) · NAC B01 · about 8 mi away
Control 139.2625, 139.8125
Voice 139.1125, 150.875, 152.7125, 169.675
Deerfield · WISCOM
RFSS 1 · Site 1 (hex 1) · NAC b05 · about 13 mi away
Control 139.9125, 152.1125, 152.5175, 152.6525
Voice 151.07, 155.355
DOC Oakhill · WISCOM
RFSS 1 · Site 210 (hex D2) · NAC B0C · about 21 mi away
Control 773.08125, 773.33125, 774.28125, 774.53125, 774.78125
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Sumner?

We do not have a fire dispatch channel listed specifically for Sumner. The county-level fire dispatch channels in the same county: Jefferson County Fire 154.0550 MHz, narrow FM, 107.2 PL.

What scanner do I need to listen to fire and EMS in Sumner?

The analog conventional channels can be heard on any scanner; a scanner that decodes P25 is needed for the digital conventional channels.

What are the control channels for trunked radio in Sumner?

For Sumner, start with the Milton site of WISCOM. Its control channels are 139.2625, 139.8125 MHz. Program a control channel first; the scanner finds the voice channels from it.