Skip to content

McLean Fire and EMS Frequencies

We do not have frequencies listed specifically for McLean in Pierce County, Nebraska yet. Countywide channels for Pierce County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Hartington (Nebraska State Radio System), about 20 miles away.

About McLean Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers McLean: Pierce County Fire 154.2050 MHz, narrow FM, 134 DPL. Trunked: Nebraska State Radio System, for example Pierce County Fire talkgroup 54003 (hex d2f3).

  • 6 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Nebraska State Radio System: 1 talkgroup. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For McLean, start with the Hartington site of Nebraska State Radio System, about 20 miles away. Its control channels: 155.31, 155.565 MHz.

Data updated .

Pierce County channels that also cover McLean

Fire Dispatch

Fire Dispatch frequencies for Pierce County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Pierce County FirePierce County Fire – Dispatch – South154.2050134 DPLFMNWQGZ377
Pierce County FirePierce County Fire – Dispatch – North154.2050243 DPLFMNWQGZ377

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Pierce County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Pierce County FireCounty Fireground153.8675FMN—
Pierce County FireCounty Fireground153.9575FMN—
Pierce County FireCounty Fireground154.3025FMN—
Pierce County FireCounty Fireground155.1225FMN—

Nebraska State Radio System

Nebraska State Radio System talkgroups
AgencyDescriptionTalkgroupHexMode
Pierce County FireFire and Rescue54003d2f3D

Nearest trunked radio sites

Distances are measured from the center of McLean.

Hartington · Nebraska State Radio System
RFSS 1 · Site 64 (hex 40) · NAC B84 · about 20 mi away
Control 155.31, 155.565
Voice 154.01, 154.68
Norfolk 800 · Nebraska State Radio System
RFSS 1 · Site 95 (hex 5F) · about 24 mi away
Control 854.1625, 854.3125, 854.4625
Voice 854.0125
Norfolk · Nebraska State Radio System
RFSS 1 · Site 66 (hex 42) · NAC B8B · about 26 mi away
Control 155.25, 155.5875
Voice 154.0475, 154.325, 154.905, 155.9475
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in McLean?

We do not have a fire dispatch channel listed specifically for McLean. The county-level fire dispatch channels in the same county: Pierce County Fire 154.2050 MHz, narrow FM, 134 DPL.

Do fire departments and EMS use a trunked radio system in McLean?

Yes. The county-level systems that cover McLean are Fire and EMS talkgroups are listed for Nebraska State Radio System: 1 talkgroup. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in McLean?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in McLean?

For McLean, start with the Hartington site of Nebraska State Radio System. Its control channels are 155.31, 155.565 MHz. Program a control channel first; the scanner finds the voice channels from it.