Skip to content

Chalk Level Fire and EMS Frequencies

We do not have frequencies listed specifically for Chalk Level in St. Clair County, Missouri yet. Countywide channels for St. Clair County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Deepwater (Missouri Statewide Wireless Interoperable Network (MOSWIN)), about 8 miles away.

About Chalk Level Fire and EMS Frequencies

Quick answer: County-level ems dispatch that covers Chalk Level: Ellett Memorial Hospital 155.1600 MHz, narrow FM, 88.5 PL; St. Clair County Rescue Squad 155.4000 MHz, narrow FM, 141.3 PL.

  • 7 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.

Data updated .

St. Clair County channels that also cover Chalk Level

Fire Ground / Tactical

Fire Ground / Tactical frequencies for St. Clair County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Roscoe Township FireRoscoe Township Fire – Operations154.0700CSQFMNWPFI886
Sac-Osage Fire Protection DistrictSac-Osage Fire Protection District – Operations154.2350210.7 PLFMNWPKX626
St. Clair County Rescue SquadRescue Operations .154.2050141.3 PLFMNKNNV359

EMS Dispatch

EMS Dispatch frequencies for St. Clair County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Ellett Memorial HospitalEllett Memorial Hospital – Paging /Operations .155.160088.5 PLFMNKXZ410
St. Clair County Rescue SquadHospital PVT – Dispatch/Operations .155.4000141.3 PLFMNWNUW241

EMS Tactical

EMS Tactical frequencies for St. Clair County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Sac-Osage Hospital and Ambulance Service (Osceola)EMS .155.2800FMNKXX498

Hospitals & Medical

Hospitals & Medical frequencies for St. Clair County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Sac-Osage Hospital and Ambulance Service (Osceola)Patient Reports .155.3400CSQFMNKXX498

Nearest trunked radio sites

Distances are measured from the center of Chalk Level.

Deepwater · Missouri Statewide Wireless Interoperable Network (MOSWIN)
RFSS 5 · Site 3 (hex 3) · NAC 1CC · about 8 mi away
Control 154.6875, 169.775
Voice 159.21, 169.8875, 171.3875
Osceola 700 · Missouri Statewide Wireless Interoperable Network (MOSWIN)
RFSS 1 · Site 57 (hex 39) · NAC 1C6 · about 9 mi away
Control 773.06875, 773.31875
Voice 773.56875, 773.81875, 774.06875, 774.31875
Cedar Springs 700 · Missouri Statewide Wireless Interoperable Network (MOSWIN)
RFSS 1 · Site 90 (hex 5A) · NAC 1CA · about 20 mi away
Control 769.19375, 769.44375
Voice 769.69375, 769.94375, 770.19375, 770.44375
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does EMS or the ambulance service use in Chalk Level?

We do not have a EMS dispatch channel listed specifically for Chalk Level. The county-level EMS dispatch channels in the same county: Ellett Memorial Hospital 155.1600 MHz, narrow FM, 88.5 PL; St. Clair County Rescue Squad 155.4000 MHz, narrow FM, 141.3 PL.

What scanner do I need to listen to fire and EMS in Chalk Level?

The analog conventional channels can be heard on any scanner.

What are the control channels for trunked radio in Chalk Level?

For Chalk Level, start with the Deepwater site of Missouri Statewide Wireless Interoperable Network (MOSWIN). Its control channels are 154.6875, 169.775 MHz. Program a control channel first; the scanner finds the voice channels from it.