Skip to content

Belpre Fire and EMS Frequencies

We do not have frequencies listed specifically for Belpre in Edwards County, Kansas yet. Countywide channels for Edwards County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Fellsburg (Kansas Statewide Interoperable Communication System (KSICS)), about 10 miles away.

About Belpre Fire and EMS Frequencies

Quick answer: Trunked: Kansas Statewide Interoperable Communication System (KSICS), for example Edwards County Fire talkgroup 707 (hex 2c3).

  • Trunked radio systems that carry fire and EMS traffic here: Kansas Statewide Interoperable Communication System (KSICS): 2 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Belpre, start with the Fellsburg site of Kansas Statewide Interoperable Communication System (KSICS), about 10 miles away. Its control channels: 852.3125, 852.6125 MHz.

Data updated .

Edwards County channels that also cover Belpre

Kansas Statewide Interoperable Communication System (KSICS)

Kansas Statewide Interoperable Communication System (KSICS) talkgroups
AgencyDescriptionTalkgroupHexMode
Edwards County FireEdwards County Fire – Dispatch7072c3D
Edwards County EMSEdwards County EMS – Dispatch6862aeD

Nearest trunked radio sites

Distances are measured from the center of Belpre.

Fellsburg · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 1 · Site 20 (hex 14) · NAC 1B4 · about 10 mi away
Control 852.3125, 852.6125
Voice 851.6, 852.9375, 853.1875, 853.65
Kinsley · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 1 · Site 62 (hex 3E) · NAC 1B0 · about 13 mi away
Control 854.5125, 856.0125
Preston · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 1 · Site 16 (hex 10) · NAC 1BA · about 32 mi away
Control 852.2375, 852.9
Voice 851.9, 853.25, 853.5, 853.925
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

Do fire departments and EMS use a trunked radio system in Belpre?

Yes. The county-level systems that cover Belpre are Fire and EMS talkgroups are listed for Kansas Statewide Interoperable Communication System (KSICS): 2 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Belpre?

A trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Belpre?

For Belpre, start with the Fellsburg site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels are 852.3125, 852.6125 MHz. Program a control channel first; the scanner finds the voice channels from it.