Skip to content

Murray Fire and EMS Frequencies

We do not have frequencies listed specifically for Murray in Clarke County, Iowa yet. Countywide channels for Clarke County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Van Wert (Iowa Statewide Interoperable Communications System (ISICS)), about 14 miles away.

About Murray Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Murray: Clarke County Fire 154.2200 MHz, FM, no tone. Trunked: Iowa Statewide Interoperable Communications System (ISICS), for example Clarke County Fire talkgroup 22710 (hex 58b6).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Iowa Statewide Interoperable Communications System (ISICS): 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Murray, start with the Van Wert site of Iowa Statewide Interoperable Communications System (ISICS), about 14 miles away. Its control channels: 769.95625, 770.20625, 770.45625 MHz.

Data updated .

Clarke County channels that also cover Murray

Fire Dispatch

Fire Dispatch frequencies for Clarke County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Clarke County FireClarke County Fire – Dispatch154.2200FMWQHD239

Iowa Statewide Interoperable Communications System (ISICS)

Iowa Statewide Interoperable Communications System (ISICS) talkgroups
AgencyDescriptionTalkgroupHexMode
Clarke County FireCounty Fire Patch2271058b6T
Clarke County FireCounty Fire Tactical2271258b8T
Clarke County EMSClarke County EMS – Dispatch2271858beT

Nearest trunked radio sites

Distances are measured from the center of Murray.

Van Wert · Iowa Statewide Interoperable Communications System (ISICS)
RFSS 1 · Site 89 (hex 59) · NAC 4C0 · about 14 mi away
Control 769.95625, 770.20625, 770.45625
Voice 769.70625
Union Co Simulcast · Iowa Statewide Interoperable Communications System (ISICS)
RFSS 2 · Site 64 (hex 40) · NAC 4C2 · about 16 mi away
Control 770.90625, 774.53125, 774.78125
Voice 770.65625
Winterset · Iowa Statewide Interoperable Communications System (ISICS)
RFSS 1 · Site 61 (hex 3D) · NAC 4C0 · about 21 mi away
Control 773.04375, 773.54375, 774.04375
Voice 770.95625
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Murray?

We do not have a fire dispatch channel listed specifically for Murray. The county-level fire dispatch channels in the same county: Clarke County Fire 154.2200 MHz, FM, no tone.

Do fire departments and EMS use a trunked radio system in Murray?

Yes. The county-level systems that cover Murray are Fire and EMS talkgroups are listed for Iowa Statewide Interoperable Communications System (ISICS): 3 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Murray?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Murray?

For Murray, start with the Van Wert site of Iowa Statewide Interoperable Communications System (ISICS). Its control channels are 769.95625, 770.20625, 770.45625 MHz. Program a control channel first; the scanner finds the voice channels from it.