Hecker also extends into St. Clair County.
About Hecker Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Hecker: Monroe County Fire 453.3875 MHz, narrow FM, 343 DPL. Trunked: STARCOM21 Statewide Illinois, for example Monroe County Fire talkgroup 7254 (hex 1c56).
- 4 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: STARCOM21 Statewide Illinois: 10 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Hecker, start with the St. Clair Co Simulcast site of STARCOM21 Statewide Illinois, about 10 miles away. Its control channels: 851.225, 851.5625, 852.1625 MHz.
- 2 listed entries are marked encrypted. No scanner can decode encrypted audio.
Data updated .
Hecker conventional frequencies
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Hecker Fire | Hecker Fire – Fire Ground | 154.2500 | FMN | KBI958 | |
| Hecker Fire | Hecker Fire – Fire Ground | 154.2500 | 91.5 PL | FMN | KBI958 |
Monroe County channels that also cover Hecker
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Monroe County Fire Backup | Monroe County Fire – Tone-Outs | 154.1900 | 167.9 PL | FMN | KSI389 |
| Monroe County Fire | Monroe County Fire – Paging /Dispatch UHF (Waterloo) | 453.3875 In 458.3875 | 343 DPL | FMN | WQFN216 |
STARCOM21 Statewide Illinois
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Monroe County Fire | Columbia Citywide / Fire Operations | 7254 | 1c56 | D |
| Monroe County Fire | Monroe County Fire – Tone-Outs/Dispatch/Response | 7999 | 1f3f | D |
| Monroe County Fire | Prairie Du Rocher Fire – Paging/Tone-Outs | 29007 | 714f | D |
| Monroe County Fire | Monroe County Fire – Tactical Channel | 8000 | 1f40 | D |
| Monroe County Fire | Monroe County Fire – Tactical Channel | 8001 | 1f41 | D |
| Monroe County Fire | Monroe County Fire – Tactical Channel | 8002 | 1f42 | D |
| Monroe County Fire | Monroe County Fire – Tactical Channel | 8003 | 1f43 | D |
| Monroe County EMS | Monroe County EMS – Dispatch – Countywide | 8005 | 1f45 | D |
2 encrypted talkgroups (cannot be monitored)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Monroe County EMS | Monroe Co EMS – Paging/Dispatch (mobiles ENC) | 29006 | 714e | D Encrypted |
| Monroe County EMS | Monroe County EMS – Operations 29001 | 29001 | 7149 | D Encrypted |
Nearest trunked radio sites
Distances are measured from the center of Hecker.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Hecker?
We do not have a fire dispatch channel listed specifically for Hecker. The county-level fire dispatch channels in the same county: Monroe County Fire 453.3875 MHz, narrow FM, 343 DPL.
Do fire departments and EMS use a trunked radio system in Hecker?
Yes. The county-level systems that cover Hecker are Fire and EMS talkgroups are listed for STARCOM21 Statewide Illinois: 10 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Hecker?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Hecker?
For Hecker, start with the St. Clair Co Simulcast site of STARCOM21 Statewide Illinois. Its control channels are 851.225, 851.5625, 852.1625 MHz. Program a control channel first; the scanner finds the voice channels from it.
Are Hecker fire and EMS frequencies encrypted?
None of the 2 conventional frequencies listed for Hecker are marked encrypted.