About Hiram Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Hiram: Paulding County Fire 154.1750 MHz, narrow FM, 107.2 PL. Trunked: Paulding County Government (GA), for example Paulding County Fire talkgroup 200 (hex c8).
- 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: Paulding County Government (GA): 3 talkgroups; Paulding County Government (P25) (Project 25): 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Hiram, start with the Dallas 1 site of Paulding County Government (GA), about 6 miles away. Its control channels: 453.2375 MHz.
- 2 listed entries are marked encrypted. No scanner can decode encrypted audio.
Data updated .
Paulding County channels that also cover Hiram
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Paulding County Fire | Paulding County Fire – Dispatch | 154.1750 In 159.5100 | 107.2 PL | FMN | WNCX657 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Paulding County Fire | Sheriff-Fire – Interop | 154.3100 In 159.0675 | FMN | WNCX657 | |
| Paulding County Fire | Paulding County Fire – Tactical Channel | 159.5100 | FMN | WNCX657 |
Paulding County Government (GA)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Paulding County Fire | Paulding County Fire – Dispatch | 200 | c8 | T |
| Paulding County Fire | Paulding County Fire – Fire Ground | 202 | ca | T |
| Paulding County Fire | Paulding County Fire – Tactical Channel | 211 | d3 | T |
Paulding County Government (P25)
Project 25
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Paulding County Fire | County Fire Rescue – 10213 | 10213 | 27e5 | T |
2 encrypted talkgroups (cannot be monitored)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Paulding County Fire | County Fire Rescue – Dispatch | 10200 | 27d8 | T Encrypted |
| Paulding County Fire | County Fire Rescue – 10202 | 10202 | 27da | T Encrypted |
Nearest trunked radio sites
Distances are measured from the center of Hiram.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Hiram?
We do not have a fire dispatch channel listed specifically for Hiram. The county-level fire dispatch channels in the same county: Paulding County Fire 154.1750 MHz, narrow FM, 107.2 PL.
Do fire departments and EMS use a trunked radio system in Hiram?
Yes. The county-level systems that cover Hiram are Fire and EMS talkgroups are listed for Paulding County Government (GA): 3 talkgroups; Paulding County Government (P25) (Project 25): 3 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Hiram?
The analog conventional channels can be heard on any scanner; a trunking scanner that supports Project 25 is needed for the trunked talkgroups.
What are the control channels for trunked radio in Hiram?
For Hiram, start with the Dallas 1 site of Paulding County Government (GA). Its control channels are 453.2375 MHz. Program a control channel first; the scanner finds the voice channels from it.