Skip to content

Flagler Fire and EMS Frequencies

We do not have frequencies listed specifically for Flagler in Kit Carson County, Colorado yet. Countywide channels for Kit Carson County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Flagler (State of Colorado DTRS), about 3 miles away.

About Flagler Fire and EMS Frequencies

Quick answer: County-level ems dispatch that covers Flagler: Kit Carson County EMS 462.9500 MHz, narrow FM, 94.8 PL. Trunked: State of Colorado DTRS, for example Kit Carson County Fire talkgroup 424 (hex 1a8).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: State of Colorado DTRS: 5 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Flagler, start with the Flagler site of State of Colorado DTRS, about 3 miles away. Its control channels: 852.2875, 852.5625, 852.8125 MHz.

Data updated .

Kit Carson County channels that also cover Flagler

EMS Dispatch

EMS Dispatch frequencies for Kit Carson County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Kit Carson County EMSKit Carson County EMS – Flagler462.9500
In 467.9500
94.8 PLFMNKAQ249
Kit Carson County EMSKit Carson County EMS – Bethune462.9500
In 467.9500
136.5 PLFMNKAQ249

State of Colorado DTRS

State of Colorado DTRS talkgroups
AgencyDescriptionTalkgroupHexMode
Kit Carson County FireKit Carson County Fire – Dispatch4241a8D
Kit Carson County FireKit Carson County Fire – Fire Ground4251a9D
Kit Carson County FireHazmat4271abD
Kit Carson County EMSKit Carson County EMS – Dispatch4221a6D
Kit Carson County EMSKit Carson County EMS – Tactical Channel4231a7D

Nearest trunked radio sites

Distances are measured from the center of Flagler.

Flagler · State of Colorado DTRS
RFSS 1 · Site 27 (hex 1B) · NAC D1B · about 3 mi away
Control 852.2875, 852.5625, 852.8125, 853.6
Voice 851.1125, 851.4375
Boyero · State of Colorado DTRS
RFSS 1 · Site 22 (hex 16) · NAC D16 · about 17 mi away
Control 851.85, 852.725, 853.1375, 853.3125
Voice 851.2375, 851.425, 854.6875, 854.9875
Hugo · State of Colorado DTRS
RFSS 1 · Site 63 (hex 3F) · NAC D1F · about 25 mi away
Control 851.9375, 852.5375, 852.8375, 853.15
Voice 851.6625, 858.1875
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does EMS or the ambulance service use in Flagler?

We do not have a EMS dispatch channel listed specifically for Flagler. The county-level EMS dispatch channels in the same county: Kit Carson County EMS 462.9500 MHz, narrow FM, 94.8 PL.

Do fire departments and EMS use a trunked radio system in Flagler?

Yes. The county-level systems that cover Flagler are Fire and EMS talkgroups are listed for State of Colorado DTRS: 5 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Flagler?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Flagler?

For Flagler, start with the Flagler site of State of Colorado DTRS. Its control channels are 852.2875, 852.5625, 852.8125, 853.6 MHz. Program a control channel first; the scanner finds the voice channels from it.