Skip to content

Westcliffe Fire and EMS Frequencies

We do not have frequencies listed specifically for Westcliffe in Custer County, Colorado yet. Countywide channels for Custer County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Verdemont (State of Colorado DTRS), about 9 miles away.

About Westcliffe Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Westcliffe: Custer County Fire 154.3850 MHz, FM, 110.9 PL. Trunked: State of Colorado DTRS, for example Custer County Fire talkgroup 449 (hex 1c1).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: State of Colorado DTRS: 7 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Westcliffe, start with the Verdemont site of State of Colorado DTRS, about 9 miles away. Its control channels: 852.9, 853.1125, 853.4 MHz.

Data updated .

Custer County channels that also cover Westcliffe

Fire Dispatch

Fire Dispatch frequencies for Custer County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Custer County FireWet Mountain Fire Protection Dist.154.3850
In 153.7700
110.9 PLFMWPKH611

State of Colorado DTRS

State of Colorado DTRS talkgroups
AgencyDescriptionTalkgroupHexMode
Custer County FireWet Mountain Fire District4491c1D
Custer County FireWetmore Fire District4501c2D
Custer County FireCounty Fire Fireground4471bfD
Custer County FireCounty Fire4511c3D
Custer County FireWet Mountain Fire District Tactical4561c8D
Custer County EMSCounty EMS4461beD
Custer County EMSCounty EMS4481c0D

Nearest trunked radio sites

Distances are measured from the center of Westcliffe.

Verdemont · State of Colorado DTRS
RFSS 6 · Site 16 (hex 10) · NAC D10 · about 9 mi away
Control 852.9, 853.1125, 853.4, 853.9375
Voice 852.3125, 856.1125
Deer Peak · State of Colorado DTRS
RFSS 6 · Site 51 (hex 33) · NAC D13 · about 17 mi away
Control 852.4625, 852.9125, 853.2, 853.5875
Voice 851.25, 851.4875, 851.7125, 851.9125, 854.2375, 854.7375, 856.0375, 857.0375
Coaldale · State of Colorado DTRS
RFSS 6 · Site 64 (hex 40) · NAC D10 · about 25 mi away
Control 852.1, 852.6, 852.9375, 853.2375
Voice 851.7875, 856.2625
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Westcliffe?

We do not have a fire dispatch channel listed specifically for Westcliffe. The county-level fire dispatch channels in the same county: Custer County Fire 154.3850 MHz, FM, 110.9 PL.

Do fire departments and EMS use a trunked radio system in Westcliffe?

Yes. The county-level systems that cover Westcliffe are Fire and EMS talkgroups are listed for State of Colorado DTRS: 7 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Westcliffe?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Westcliffe?

For Westcliffe, start with the Verdemont site of State of Colorado DTRS. Its control channels are 852.9, 853.1125, 853.4, 853.9375 MHz. Program a control channel first; the scanner finds the voice channels from it.