About Remlap Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Remlap: Blount County Fire 158.8350 MHz, narrow FM, 186.2 PL. Trunked: Alabama Interoperable Radio System (AIRS), for example Blount County Fire talkgroup 43012 (hex a804).
- 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: Alabama Interoperable Radio System (AIRS): 9 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Remlap, start with the Palmerdale site of Alabama Interoperable Radio System (AIRS), about 6 miles away. Its control channels: 854.9125, 855.6375, 857.2125 MHz.
Data updated .
Blount County channels that also cover Remlap
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Blount County Fire | Blount County Fire – Dispatch Patched to AIRS 43012 | 158.8350 In 154.0700 | 186.2 PL | FMN | KTI683 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Blount County Fire | Blount County Fire – Fire Ground | 154.3550 In 153.8300 | 186.2 PL | FMN | WNRG833 |
Hospitals & Medical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Blount County Hospital | Blount Medical Center – Patient Reports | 155.3400 | 186.2 PL | FMN | WQOK958 |
Alabama Interoperable Radio System (AIRS)
System ID 00A
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Blount County Fire | Blount County Fire – Dispatch Primary-Countywide | 43012 | a804 | T |
| Blount County Fire | Blount County Fire – Dispatch Secondary-Countywide | 43013 | a805 | T |
| Blount County Fire | North Region Fire – Tactical | 43014 | a806 | T |
| Blount County Fire | East Region Fire – Tactical | 43015 | a807 | T |
| Blount County Fire | South Region Fire – Tactical | 43016 | a808 | T |
| Blount County Fire | West Region Fire – Tactical | 43017 | a809 | T |
| Blount County Fire | Countywide Fire – Tactical | 43018 | a80a | T |
| Blount County Fire | Countywide Fire – Tactical | 43019 | a80b | T |
| Blount County EMS | Lifeguard EMS – Dispatch (AMR) | 43037 | a81d | T |
Nearest trunked radio sites
Distances are measured from the center of Remlap.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Remlap?
We do not have a fire dispatch channel listed specifically for Remlap. The county-level fire dispatch channels in the same county: Blount County Fire 158.8350 MHz, narrow FM, 186.2 PL.
Do fire departments and EMS use a trunked radio system in Remlap?
Yes. The county-level systems that cover Remlap are Fire and EMS talkgroups are listed for Alabama Interoperable Radio System (AIRS): 9 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Remlap?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Remlap?
For Remlap, start with the Palmerdale site of Alabama Interoperable Radio System (AIRS). Its control channels are 854.9125, 855.6375, 857.2125 MHz. Program a control channel first; the scanner finds the voice channels from it.